Inspur NF8480M5 – High Expansibility Computing Platform for Critical Application Load
The server supports Intel® Xeon® Scalable processors which implements the innovative “mesh” on-chip interconnect topology that delivers low latency and high bandwidth among cores, memory, and I/O controllers while improving the power efficiency. Intel Ultra Path Interconnect (UPI) links is used to achieve direct communication between processors.
It supports 48 DDR4 DIMMs with 50% memory expandability increase and 25% bandwidth increased, thus significantly reduces the system delay caused by frequent IOs.
It supports up to 12 NVMe SSDs, with maximum read performance of 3.5GB/s.
It adopts the innovative E-SRA architecture with BMC software dual-level write protection, and independent BIOS refreshing through BMC, which ensures a safe and reliable firmware upgrade.
It leverages IMD enhanced memory protection and PCIe hot swap technology.
With its SCSA super current safety technology and the ultra-low impedance power supply, it has low line loss, high reliability, lower space occupation and higher maintenance efficiency.
Inspur NF8480M5 supports hierarchical storage schemes, with up to 24* 2.5”/3.5” hard drives, 12* U.2 NVMe SSDs and 2 built-in M.2 SSDs which can be used as OS boot drives, in order to satisfying storage requirements of different business scenarios. It supports 16 PCIe3.0 slots and 1 OCP slot. The PCIE bus resources allows flexible configuration, and support free switch between U.2 NVMe hard drive and PCIe expansion cards based on customer requirement.
The system adopts the new generation LIDS (optic channel diagnosis system) and DSFI (deep system failure insight) technology which can have real-time full access to underlying faults information, therefor greatly improving troubleshooting efficiency and accelerating the system fault recovery.
|Form factor||4U Rack mount|
|Processor||It supports 2/4 new generation Intel® Xeon® scalable processor, TDP 205W|
|Chipset||Intel® C620 Series Chipset|
|Memory||Up to 48 DIMMs, with the maximum memory frequency up to 2933 MHz; it supports RDIMM/LRDIMM ,NVDIMM and Optane™ PMem|
|Storage||Up to 24*2.5/3.5-inch SAS/SATA Drives,
up to 12*U.2 NVMe SSDs,
2 built-in M.2 SSDs, and soft RAID 0/1
|Disk controller||It supports 12G RAID card, RAID0, 1, 10, 1E, 5, 50, 6, 60, etc., and also super capacitor Cache protection, and provides RAID status migration and RAID configuration memory|
|Expansion slot||Up to 16 PCIe3.0 and 1 OCP slot|
|Front I/O||2 USB 3.0 interfaces, 1 VGA interface, 1 RJ45 system serial port and LCD diagnostic display|
|Rear I/O||4 USB 3.0 interfaces, 1 VGA interface, 1 special MGMT port, 1 BMC diagnosis serial port and 1 system serial port|
|Network||Supporting 40-gigabit; OCP NIC card and OCP PHY card, and NCS for OCP A
It supports network advanced characteristics including wake-up on LAN, network redundancy and load balancing
|Management||It supports remote management control, such as IPMI2.0, KVM over IP, SOL and SNMP; 1 rear BMC special MGMT port and 1 BMC diagnosis serial port for off-line fault diagnosis|
|Safety||It supports TPM2.0|
|Operating system||Microsoft Windows Sever, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, CentOS, VMware ESXi, etc.|
|Power supply||It supports full power grid AC inputs, 240/336V high voltage DC input and -48V low voltage DC input
It supports platinum-level 550/800/1,300/1,600W CRPS power supply module, with and 1+1/2+1 /2+2/3+1 redundancy
|Dimensions||448.0mm（W) * 175.5mm (H)* 812mm (D)|
|Working environment humidity||20%-80%RH|